Fitment: Replacement for II; Replacement for ; Replacement for 2015; Replacement for ; Replacement for Tansit, etc.
Functions: With multiple functions, read the fault , clear trouble , read the data stream, data recording, module reset, module installation, etc.
With 35 s: only need for mileage programming and ECU chip tuning function. When use up s, send back to add .
Item Type: Diagnostic Cable
Material: ABS
Description:
The cable consists of dr ers of the serial bus USB-serial (recommended dr ers ), hardware adapter and the actual for -programm.
The software interface of the for interface has main for dowums mode. You need to select the type of the vehicle or select the service mode for adapter`s firmware update or other service functions.
It currently works with the follo g platforms: Replacement For II 2004-2011; Replacement For III 2011, 2015; Replacement For I, Replacement For II; Replacement For C- ; Replacement For ; Replacement For 2015 ; Replacement For ; Replacement For Tansit; Replacement For 2008, 2015 etc.
New Released Diagnostic Adapter with neweest software V1.27.001 can replace For Focom Vehicle Communicate Module 2, just one difference, for cannot key programming, but CAN Diagnostic System for Focom can support Mileage and it is full function type.
Please Note Important:
Please Disconnect internet when Run software.
Please don t update online, otherwise it will be locked.
MUST Click No when message show out to ask you update.
Please use for or for 7 32bit system.
Highlights to get:
Software: V1.27.001
Full License Adapter: Full mode act ated, access to existing sections of the software, such as: VBF Loader, Update Wizard and Direct Config.
With 35 s: only need for mileage programming and ECU chip tuning function (When use up s, send back to add , Need pay extra cost.)
Support odometer correction
For Focom cars from 2004 to 2017 Year.
Full Mode Act ated
Best replacement for Focom Vehicle Communicate Module 2
Functions:
1. Read the fault
2. Clear trouble
3. Read the data stream
4. Data recording
5. Module reset
6. Module installation
7. Reprogram the ECU BCM and so on
8. Clear the gasbag (RCM) collision data
9. Read, backup, edit, and erase AsBuilt files
10. Read, backup, edit, and erase the underlying DirectConfig configuration file
11. Support power to enhance the brush to write, such as replacement for 2.0T 200 brush 240 , 12 85 brush 105 , 150 brush 163
12. Support VBF file directly to write
13. Support BIN file directly to write
14. Support online update vehicle entire module (Update Wizard)
15. Support replacement for MK2, 12 for MK3, ning, and other meter mileage clear, brush to write
Features:
The ard can be displayed from English to Chinese; the new replacement for power can be upgraded from low to high; the navigation OPS of replacement for Escape can be flashed; the program can be input; the device ( limited) can be replaced.
Supported Vehicles:
Replacement for MK2 (2004-2014) C307
Replacement for MK3 (2012-2017) C346
Replacement for g 15 g 17 g
Replacement for s Galay
Replacement for 13 ( 5)
Replacement for E lorer
Replacement for
Replacement for Carn al B-
Replacement for g
And other new
Allows the User to:
Diagnose the majority of car parts and components that are connected to a central electrical module (GEM, BCMii) through the data bus (CAN);
Rece e data embedded in the car components and modules, including their part number, version, calibration, serial number;
Make the necessary changes to the central configuration of the car, and change the configuration of the modules and components if necessary;
Update the calibration (firmware) of the modules and component
Возврат по недоставке
