Flexible nFEP FEP Film for Anycubic Photon Mono SE 4K 2 X X2 M3 Max Plus M5 M5s 6K 6KS SLA 3D Printer nFEP Release Liner Film
How to Choose-nFEP or FEP ?
nFEP film is an updated relase film.
When your prints are relatively simple and printing is not frequent, please choose traditional FEP film, because it can meet those basic needs and it is cheaper. But if you print more frequently, the prints are more complex, or you want to obtain more precise printing effects, then nFEP will be more suitable for you. Because nFEP release film with high precison and high printing success rate.
Better Adhesion Resistance
nFEP film also known as FPA film. It is more flexible and has better adhesion resistance. This just makes your prints better, since it won't stick to the film thus avoiding support's breakage, which means a higher success rate and longer life span.
Notice: Please remember to re-leveling your 3D printer once change FEP film to nFEP film, becuase of different thickness.
Tips for How to Reduce Adhesion
Please add supports evenly, because no matter what kind of release film it is, it has a certain adhesion, so every slight shaking when pulling up and down will cause the model to be uneven or mis-layered.
One more thing, in winter, please pay attention to the ambient temperature.
Good Replacement
Release film belongs to the consumables, once the release film is broken should be replaced in a timely manner, otherwise it will easily lead to printing failure, waste of resin, and may damage LCD screen due to leakage. So it is necessary to reserve some more release films, and the more the cheaper.
How to Protect Release Film
1. Before installation, please check if the film is intact。 If there is any damage, please contact us immediately for replacement.
2. Avoid contact with sharp tools during installation to avoid damaging the film and causing printing failure
3. After each printing failure, the impurities in the material tank must be cleaned in time.
4. When cleaning residual resin, do not use a hard plastic scraper, as the release film is very fragile and some invisible burrs may cause damage.
*If you need scraper, please choose our professional rubber scraper
Tips for Cleaning Resin Tank
Use the printer's built-in cleaning function, or manually expose the bottom layer for 10-30 seconds, then lift and remove the entire cured bottom layer to remove impurities more efficiently.
For Elegoo NFEP and FEP Release Film
There are 4 sizes for option, could be compatible for almost of Anycubic 3D printers.
*If your printer is not included in it, please contact us directly.
Compatible with:
Anycubic Photon Mono X 6KS
Anycubic Photon Mono X 6K
Anycubic Photon M5s
Anycubic Photon M5
Anycubic Photon M3 Plus
Anycubic Photon M3 Max
Anycubic Photon M3
Anycubic Photon Mono X2
Anycubic Photon Mono X
Anycubic Photon Mono 2
Anycubic Photon Mono SE
Anycubic Photon Mono 4K
Anycubic Photon Mono
Anycubic Photon D2
Anycubic Photon S
Wide Compatibility
They are suitable for any other brand 3D printers, like for Elegoo, Creality 3D, Flashforge, Monoprice, Sainsmart, Nova 3D, WanHao, Phrozen, Voxelab, QIDI, etc.
Just please measure your resin vat/tank, only if the size of the release film is larger than the resin tank, then it works for your printer.
Safe Packaging
The release film is very fragile, and to ensure that it is not damaged during international transportation, we will packed it very well.
Both sides of each film will be covered with transparent protective film. And re-packed in hardpaper envelope bag, finally, it will be put in a bubble envelope. Multiple protection to make sure what you received is in good condition.
*380x260mm release film is too large, we will roll it and packed in a hard paper tube.
Works Display
The resin models are for reference only, different printers, resin, setting may cuase different printing effects.
Works for Photon M5 Series: Photon M5 Photon M5s
Model Number: FEP Release Film
Assembly Required: no
Material: nFEP and FEP release film
Size 1: 200mm x 140mm
Size 2: 260mm x 200mm
Works for Photon Series: Photon/ Photon S/ Photon D2
Origin: Mainland China
Suitable for: Anycubic Photon Mono SLA Resin 3D Printer
Item Type: Heat Paper
Control Method: Touch
High-concerned chemical: None
semi_Choice: yes
Works for Photon M3 Series: Photon M3/ Photon M3 Max/ Photon M3 Plus
Item Name: nFEP FEP Film for Anycubic Photon Mono SLA Resin 3D Printer
Item Shape: Others
Size 3: 290mm x 210mm
Works for Mono Series: Photon Mono/ Photon Mono SE// Photon Mono 4K/ Photon Mono 2/ Photon Mono X/ Photon Mono X2/ Photon Mono X 6K/ Photon Mono X 6KS