MENABO CLOVER DX Roof Bike Rack Right Side Fatbike E-bike Black

MENABO CLOVER DX Right-Side Roof Bike Holder Fatbike E-bike Black

✅The new replacement for the iconic Menabo CHRONO bike holder, created for even greater convenience and safety of bike transport.✅

Menabo Clover DX is a roof bike holder designed to transport one bike with a maximum weight of 25 kg. The DX version has been adapted to operate the bike from the right side of the car.

The holder is suitable for electric bikes, MTBs, trekking bikes, city bikes and Fat Bikes. The mounting arm stabilizes the bike by the wheel, without direct contact with its frame.

Mounting using T-profile inserts: Yes

• right-hand version DX,

• designed to carry 1 bike,

• maximum bike weight: 25 kg,

• suitable for E-bikes, MTBs and Fat Bikes,

• mounting the bike without contact with the frame,

• adjustable and sliding rear wheel mounting,

• double anti-theft system,

• construction made of aluminum and steel,

• standard mounting in the T-channel of roof bars,

• optional external mounting for bars without a T-channel.

The Menabo Clover DX uses a front wheel locking arm.

This solution also works for bikes with unusual geometry, carbon frames and electric models.

COMFORTABLE OPERATION FROM THE RIGHT SIDE

The DX version is configured for operation from the right side of the car roof (passenger side). The lever allows you to open the locking arm, while the knob allows you to close it and properly secure the wheel.

The design makes it easy to position the bike on the rail and properly immobilize it before starting the ride.

SLIDING REAR WHEEL MOUNT

The sliding rear wheel mount allows you to adjust the holder to the length of the bike being transported. The maximum supported wheelbase is 1260 mm.

ADJUSTABLE FRONT WHEEL MOUNTING ARM

The holder is designed for bikes with wheels from 26 to 29 inches. The maximum tire width of 110 mm also allows for the transport of many Fat Bikes.

FOR E-BIKES, MTBS AND FAT BIKES

The maximum load capacity of the carrier is 25 kg, so it can be used to transport many models of e-bikes. Before loading, check the actual weight of the bike.

Clover DX is also suitable for mountain bikes, trekking bikes, city bikes and models with wide tires.

DOUBLE ANTI-THEFT SYSTEM

The carrier has two independent security features.

This solution increases safety when stationary and limits the possibility of unauthorized disassembly.

MOUNTING ON ROOF BAR

As standard, the holder is designed for mounting in the T-channel of roof bars. The minimum channel width is 20 mm, and the minimum width of the fastener head is 6.5 mm.

For bars without a suitable channel, an optional external mounting kit can be used. The kit fits bars with a cross-section from 30 × 20 mm to 55 × 30 mm.

After mounting the carrier, carefully check that all screws, clamps and fasteners to the roof bars are tight. The bike should be positioned stably on the rail and the front and rear wheels should be properly locked. You should also make sure that both anti-theft devices are properly closed.

After driving the first few kilometers, it is worth checking the stability of the entire set again and tightening the fasteners if necessary.

SAFETY OF USE

The manufacturer indicates a maximum driving speed with the holder installed of 130 km/h. However, you should always adhere to the lower limit specified in the regulations, the vehicle manual or the roof rack manufacturer's recommendations.

When driving, take into account the increased vehicle height, the effect of side winds and the change in the vehicle's handling characteristics.

FAQ - FREQUENTLY ASKED QUESTIONS QUESTIONS

1. Is the holder suitable for an electric bike?

Yes. The maximum weight of the bike that can be transported is 25 kg. Before loading, check the actual weight of the bike.

2. Does the mounting arm touch the bike frame?

No. The bike is stabilized by the wheel, so the arm does not clamp directly to the frame.

3. Is the holder suitable for a fat bike?

Yes. The holder supports tires up to 110 mm wide and wheels from 26 to 29 inches.

4. What does the DX marking mean?

DX denotes the right-hand version. The carrier mechanism is designed for operating and loading a bicycle from the right side of the car roof (passenger side).

5. Does the carrier have anti-theft protection?

Yes. The product is equipped with a lock for the transported bicycle and a lock for the carrier mounted on the bars.

6. Does the carrier fit bars without a T-channel?

Yes, with the optional external mounting kit. The kit is designed for bars with a cross-section from 30 × 20 mm to 55 × 30 mm.

7. How many bikes can be transported?

The carrier is designed to transport one bike with a maximum weight of 25 kg.

Manufacturer: Menabo Model: Clover DX Type: roof bike rack Operating side: right Number of transported bikes: 1 Maximum load capacity: 25 kg Handle weight: 5.9 kg Material: aluminum and steel Handle length: 159.3 cm Handle width: 32 cm Supported wheel size: from 26 to 29 inches Maximum tire width: 110 mm Maximum bike wheelbase: 1260 mm Compatibility with electric bikes: yes Compatibility with fat bikes: yes Bike security: yes Handle security: yes Mounting using clamps: optional after purchasing the ME/0001227 kit Note: The optional external mounting kit is not included with the carrier as standard.