Carmate Inno Frame-Hold Cycle Carrier, Matte Black, Made In Japan, IN385BK

[Base Carrier Compatibility] ●Compatible Bars - Compatible only with INNO Square Bars (23 x 32mm). ●Installation Requirements - Minimum clearance between bar and roof: 30mm or more - Front-to-back bar spacing: 600-800mm - Required installation width: 220mm *Installation across stays is prohibited.

[Bicycle Compatibility] ●Bicycle Size - Measured perpendicularly from the underside of the down tube, the ground must be 530mm above the ground. - The distance from the center of the crank to the ground must be 300mm or less. - Wheelbase must be 1200mm or less. ● Tire Size ・MTB: 20-26in / Road: 650/700c / Junior: 16-20in ・Width: Up to 55mm (including blocks) ●Downtube Section Size ・22-60mm (Not compatible with carbon frames) ●Maximum Load Capacity ・17kg (1 bicycle)

[Tools Required] ●A 10mm wrench is required to install this product.

[Warning] ●Please read the instruction manual before use. ●Maximum load capacity may be limited depending on the vehicle model. Be sure to check the vehicle compatibility chart. ●Please check the vehicle or carrier instruction manual to ensure that the carrier you are installing this product on is strong enough. ●Before riding, check that knobs, belts, etc. are tight. ●Do not modify this product. ●Adjust the front-to-back spacing of the base carrier to 600-800mm. ●Do not load anything other than bicycles. ●Do not load more than two bicycles on one attachment. ● Attach the attachment so that the bicycle handlebars do not extend beyond the width of the vehicle. ● Obey the legal speed limit, and reduce your speed especially in strong winds. ● Do not ride on rough roads. ● Always measure the height of the vehicle with the bicycle loaded before riding, and do not enter parking lots, tunnels, etc. that are lower than that height. ● Do not use a bicycle storage case or waterproof sheet when loading. ● If the belt is cracked, damaged, or deteriorated, discontinue use immediately and replace it with a new one. ● Always lock the key when loading a bicycle.

[Caution] ● Do not leave the bicycle loaded for long periods of time. ● Avoid sudden acceleration, sudden braking, and abrupt steering wherever possible. ● Do not hit the rear gate or trunk against the attachment or bicycle. ● Remove the attachment or carrier before putting the bicycle through a car wash. ● Load and unload bicycles on a stable, flat surface.

Recommended Vehicle Types [Compatible with a wide range of vehicles, from compact cars to SUVs] *Not compatible with kei cars (under the Road Traffic Act, kei cars cannot carry luggage exceeding 2.5m in height plus cargo volume).

●SUV ・Land Cruiser/X-Trail/Vezel/Forester/CX-60, etc. ●Compact Car ・Aqua/Fit/Yaris, etc. ●Station Wagon ・Levorg/Corolla Sport, etc. ●Hatchback ・Civic/Prius, etc. ●Minivan ・Noah/Serena/Step WGN, etc. ●This frame-mounted cycle attachment eliminates the need to remove the front wheel. You can simply mount your bike without removing the front wheel. The ratchet belt is made of soft plastic to prevent wheel damage. The locking knob that clamps the down tube can be rotated left or right, allowing it to be attached to either the driver's or passenger's side. ●Black model that blends seamlessly with the base carrier. The frame has a bold matte black finish. ●Firmly attaches to the INNO square bar. Evaluation tests have confirmed that there is no shifting or loosening. When no bicycle is loaded, the arm section can be tilted backwards to lower the mounting height. ●The frame is made of aluminum, making the product lightweight. It comes with a key lock, and a lock cover can be attached to the lock knob that clamps the bicycle's down tube. ●The required mounting width is only 220mm, making it easy to load multiple items. ●Can be washed with water! If the product gets dirty with mud or other debris, remove the dirt with water or a towel and dry it thoroughly in the shade.