Feature:
1. Highspeed ABEC5 ultradurable sealed bearings, low friction, low noise, high accuracy, and longlasting use. 3.5mm goldplated connector, 3.175mm output shaft, suitable for 110, 112 brushless RC cars.
2. High balance explosion?proof rotor, high smoothness, high speed, dynamic balance control within 10mg, it can be disassembled and replaced later. Ultra?thin silicon steel sheet, excellent performance, high magnetic permeability, high silicon content, good insulation and heat resistance.
3. It adopts 4?level 12?slot high?torque motor design, which can realize maximum power conversion. CNC machined steel billet, 6061?T6 aluminum heat sink, secondary oxidation treatment, high?end and fine appearance.
4. The motor adopts precise waterproof design, maximum power conversion, high?purity copper coil, maximum efficiency, temperature resistance 180?200 celsius . Multiple protection functions, battery low?voltage cut?off protection, overheating signal loss protection, motor stall protection.
5. Using M3 screws, a variety of installation styles. Powerful current resistance, excellent heat dissipation, easy to program and compatible with pocket programming cards.
Specification:
Item Type: RC Sensorless Brushless Motor + ESC Kit
Material: Plastic+Metal+Electronic Component
Color: Red and Black
2845 Motor:
KV (RPMVolt): 3800kv
Wattage: 800
Maximum Speed: 50000
Maximum Voltage: <14V
Maximum Ampere: 57A
Number Of Rotor Poles: 4
Shaft Diameter: Approx. 3.175mm0.125in
Shaft Length: Approx. 15mm 0.59in
Diameter: Approximately. 28mm 1.1in
Length: Approx. 47mm 1.9in
Connector: Approx. 3.5mm0.14in
45A ESC:
Continuous Current: 45A
Maximum Current: 240A
Motor Type: Sensorless and brushless motor
For Lipo 2s Or 6 Nimh Cells:
1. For Highway: 3656 size or smaller engine with kv <5600kv
2. OffroadTruck
: 3656 or smaller motor with KV <3900
For Lipo 3s Or 9 Nimh Cells:
1. For Highway: 3656 size or smaller engine with kv <3800kv
2. For OffroadTruck
: 3656 size or smaller motor with KV <2700
Resistance: 0.0014ohm
Battery: 23s lipo49 battery nimh
Bec Output: 5.8v 3A (switch mode)
Size: Approx. 51.5x38.5x38.5mm2.03x1.5x1.5in
Compatible: Suitable for 110 112 RC cars.
How To Use:
1. Connect the BEC cable to the receiver.
2. Use ESC to connect the motor cable.
3. Turn on the transmitter.
4. Connect the battery pack to the ESC, and then turn on E.
5. After the connection between the motor and the battery is completed, the motor emits a "beep beepbeep beep beep".
6. When the throttle stick is in the neutral position, the electric motor will beep again
7. ESC is feasible.
Clearing of Fault:
1. If the motor fails to work and no sound is emitted after poweron, please check the connection between the battery pack and the motor.
2. If the power indicator light flashes, please check the voltage of the battery pack, the voltage should be 5V13V. Signal lines, etc. Please check the transmitter TH. Adjust and adjust until the motor beeps again.
3. If The Motor Emits A "beep Beep Only" Sound, Please check all connections: BEC wire, transmitter and remote control.
4. If it cannot accelerate, please check that the battery voltage is too low or the temperature of the ESC is too high. If the battery voltage is too low, replace the battery. If the temperature of the ESC is too high, please check all connections. If it is not, press the EPA button on the remote control.
5. If the RC car suddenly stops under working conditions, please check the motor connection and roadblocks
6. If the RC car is driving in the opposite direction (transmitter can be used), please swap the two wires between the ESC and the motor..
Package List:
1 x RC Brushless Motor1 x 45A Waterproof ESC2 x Instructions
Note:
1. Due to manual measurement, please allow an error of 1‑3mm. Thank you!2. The monitor calibration is inconsistent, and the color of the item shown in the photo may be slightly different from the actual object. Please refer to the actual one.3. Before using this ESC in water, please remove the cooling fan; clean and dry it immediately after use to prevent the connector from rusting.Highspeed ABEC5 ultradurable sealed bearings, low friction, low noise, high accuracy, and longlasting use. 3.5mm goldplated connector, 3.175mm output shaft, suitable for 110, 112 brushless RC cars.
High balance explosion?proof rotor, high smoothness, high speed, dynamic balance control within 10mg, it can be disassembled and replaced later. Ultra?thin silicon steel sheet, excellent performance, high magnetic permeability, high silicon content, good
It adopts 4?level 12?slot high?torque motor design, which can realize maximum power conversion. CNC machined steel billet, 6061?T6 aluminum heat sink, secondary oxidation treatment, high?end and fine appearance.
The motor adopts precise waterproof design, maximum power conversion, high?purity copper coil, maximum efficiency, temperature resistance 180?200 celsius . Multiple protection functions, battery low?voltage cut?off protection, overheating signal loss protection,
Using M3 screws, a variety of installation styles. Powerful current resistance, excellent heat dissipation, easy to program and compatible with pocket programming cards.
